UPS-MER2000 specification sheet

Features:

• True online double conversion.
• Mimic LCD display with multifunction parameter settings & operational status.
• Wide input voltage range for the hashest environment.
• Support generator input.
• Cold start function is built-in.
• Bundled communication software supports Windows application etc.
• Matching battery pack.
• 3-level intelligent charging modes.
• Support economic operation mode.
• Super powerful charger for battery backup extension.
• Output power factor 0,9.
• >90% high efficiency models available.

Specifications:

©2026 Respective owners and brand holders. This table has been carefully researched and generated by ComXpert International CC (//www.comx-computers.co.za), however, errors and omissions may occur. Only references to South Africa apply. All products are sourced in South Africa from the official suppliers and the warranty is that of the local supplier. E&OE. This table and our site's content may be used on condition that this notice and link remains intact and unaltered.
Specifications
Product Code	UPS-MER2000
MODEL	UDC9102S
Phase	Single phase with ground
Capacity	2000VA / 1800W
INPUT
Rated voltage	100/110/115/120/127VAC or 200/208/220/230/240VAC
Voltage range	55-145VAC or 110-300VAC
Frequency range	40Hz - 70Hz (auto detect)
Power factor	>=0,99
Bypass voltage range high voltage point	For 200/208/220/230/240 VAC models: 230-264: setting the high voltage point in LCD from 230Vac to 264Vac (default 264Vac) For 100/110/115/120/127 VAC models: 115-132: setting the high voltage point in parameter 3 from 115Vac to 132Vac (default 132Vac)
Bypass voltage range low voltage point	For 200/208/220/230/240 VAC models: 170-220: setting the low voltage point in LCD from 170Vac to 220Vac (default 170Vac) For 100/110/115/120/127 VAC models: 95-110: setting the low voltage point in parameter 3 from 95Vac to 110Vac (default 95Vac)
ECO range	Same as the bypass
Generator input	Support
OUTPUT
Phase	Single phase & Ground
Rated voltage	100/110/115/120/127VAC or 200/208/220/230/240VAC
Power factor	0.9
Voltage regulation	+-1%
Frequency range(Utility. mode)	47-53Hz(for 50Hz) or 57-63Hz(for 60Hz)
Frequency range(batt. mode)	50/60Hz+-0.01Hz
Crest factor	0.125694444444444
THDv	<3% with linear load, <6% with non linear load
Waveform	Pure Sinewave
EFFICIENCY
AC mode (full load)	>89%
BATTERY
Voltage	48Vdc
Quantity	4pcs
Capacity (standard unit)	12V/9AH
Backup	Long run unit depends on the capacity of external batteries
Recharge time to 90%	4 hours
Charging current (built-in/Max)	1A, Max 12A
	Utility to battery: 0ms, Utility to bypass: <4ms
TRANSFER TIME
PROTECTION
Overload AC mode	105%-110%:UPS shuts down after 10min at battery mode or transfer to bypass when the utility is normal Ambient temp< 35 C 110%-130%:UPS shuts down after 1 min at battery mode or transfer to bypass when the utility is normal >130% UPS shuts down after 3 sec
Overload bat. mode	105%-110%:UPS shuts down after 1min at battery mode or transfer to bypass when the utility is normal 35 C110% UPS shuts down after 3 sec at battery mode or transfer to bypass when the utility is normal
Overload bypass mode	10A(Input breaker) 16A(Input breaker) 20A(Input breaker)
Short circuit	Hold whole system
Overheat	Line mode: Switch to bypass: Backup Mode: Shut down UPS immediately
Battery low	Alarm and switch off
EPO (optional)	Shut down UPS immediately
Battery	Advanced battery management
ALARM
Audible & visual	Line failure, low battery, overload, system fault
DISPLAY
Status LED & LCD	Line mode, backup mode, eco mode, bypass mode, low battery, bad battery, overload and UPS fault
Reading on the LCD	Input voltage, input frequency, output voltage, output frequency, load percentage, battery voltage
PHYSICAL
Standard Dimension (WxHxD)	144x209x399
Model Weight (kg)	17
COMMUNICATION INT	ERFACE
Communication port	RS232 or USB
Communication slot	SNMP Card, relay card etc
ENVIROMENT
Operating temperature	0 C-40 C
Humidity	20-90% non condensing
Altitude	< 1500m (derating while >1500m)
Noise	<50dB(at 1 meter)
SAFETY CONFORMAN	CE
	IEC/EN62040-1-1, IEC/EN62040-2